Shop

Shop

Filter Products Showing 1 - 18 of 484 results
Sort By
Price
Categories
Viscosity
Foam Safe
Odorless
Paint Finish
Filter selected
  • Bob Smith CA Extenter Tips #301 (Pack of 6)Quick view

    Bob Smith CA Extenter Tips #301 (Pack of 6)

    $4.49
    For use over Bob Smith's standard #312 top. These be used with all thicknesses of Cyanoacrylate glue from Bob Smith with the except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application. Item comes packaged in a pack of 6.
    Add to cart
    Compare
  • Bob Smith CA Extra Long Extender Tips #303 (Pack of 6)Quick view

    Bob Smith CA Extra Long Extender Tips #303 (Pack of 6)

    $3.99
    For use over the standard Bob Smith Industries #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone. Sold in a pack of 6.
    Add to cart
    Compare
  • Bob Smith CA Fine Tip Non-clog Applicators #322 6" (Pack of 5)Quick view

    Bob Smith CA Fine Tip Non-Clog Applicators #322 6″ (Pack of 5)

    $4.99
    Fine Tip Non-clog 6" long pipette for the application for thin CA glues. Can also be used for the fine application of Insta-Set accelerator and for applying fine lubricating oils. CA can be kept in the applicator for two weeks. Sold in a pack of 5
    Add to cart
    Compare
  • Bob Smith CA Pocket Extender Tips #304 (Pack of 6)Quick view

    Bob Smith CA Pocket Extender Tips #304 (Pack of 6)

    $4.49
    For use with Bob Smith Industries Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas. Sold in a pack of 6. Bob Smith #314 cap not included.
    Add to cart
    Compare
  • Bob Smith CA Regular Tip Applicators #321 (Pack of 5)Quick view

    Bob Smith CA Regular Tip Non-Clog-Applicators #321 6″ (Pack of 5)

    $4.99
    Regular Tip Non-clog 6" long pipette for the application of gap filling and extra-thick CA. CA is sucked up into the applicator by inserting it into an open CA bottle with the bulb at the end compressed, like an eyedropper. Sold in a pack of 5
    Add to cart
    Compare
  • Bob Smith Extra CA Over Cap #313 (Pack of 5)Quick view

    Bob Smith Extra CA Over Caps #313 (Pack of 5)

    $4.25
    Replacement colored caps that fit over the Bob Smith #312 top(s). Sold in a pack of 5. Color Selection: Please select your cap color or combination during the 'Customer Notes' section during checkout. We will match your request based on inventory levels.
    Add to cart
    Compare
  • Quick view

    Bob Smith Extra CA Tops #312 (Pack of 5)

    $4.49
    Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle. Sold in a pack of 5. Please Note: Caps are not capable of being interchanged with Pocket CA bottles as the diameter of the bottles are different.
    Add to cart
    Compare
  • Bob Smith Extra Fine CA Extender Tips #302 (Pack of 6)Quick view

    Bob Smith Extra Fine CA Extender Tips #302 (Pack of 6)

    $4.49
    For use over the standard #312 top from Bob Smith Industries, it allows thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.
    Add to cart
    Compare
  • Bob Smith Finish Cure 20 Minute EpoxyQuick view

    Bob Smith Finish-Cure 20 Minute Epoxy

    $13.99$32.99
    Bob Smith's Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup. Bob Smith's Finish-Cure 20 Minute Epoxy is has the least discoloration over time.
    Select options
    Compare
    Browse Wishlist
  • Bob Smith Foam-Cure Flexible Silicon Foam GlueQuick view

    Bob Smith Foam-Cure Flexible Silicone Foam Glue (Foam Safe)

    Rated 5.00 out of 5
    $5.49$7.49
    Bob Smith's FOAM-CURE is a flexible silicone based adhesive that works very well on EPP and EPO types of foams. It is crystal clear and cures to a more flexible consistency than Cyanoacrylate. It is, however, not instant bonding like Cyanoacrylate and takes roughly 15 to 30 minutes to setup. FOAM-CURE works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE requires exposure to air for drying. This product is an ORM-D regulated item and must be shipped by ground. This can equate to longer than anticipated delivery times compared to standard Priority & First Class mail packages.   
    Select options
    Compare
  • Bob Smith IC-2000 Rubber Toughened CA Super GlueQuick view

    Bob Smith IC-2000 Tire Glue Rubber Toughened CA Glue

    $8.40$9.99
    IC-2000 is a rubber-toughened cyanoacrylate glue that forms superior shock resistant bonds on non-porous surfaces.  The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. IC-2000 is well renowned in the R/C car & truck circuit as being the best adhesive for R/C car tires. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET Accelerator. For model use, IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. When cured, IC-2000 is pliable enough to be carved with a hobby knife. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
  • Bob Smith IC-Gel CA PasteQuick view

    Bob Smith IC-Gel CA Paste

    $7.25
    Bob Smith Industries IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Bob Smith Industries Maxi-Cure. IC-GEL, although it can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want. It popular with those who either assemble fishing tanks or need to patch a crack in one. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Add to cart
    Compare
  • Bob Smith Insta-Cure Super Thin Gap Filling CA GlueQuick view

    Bob Smith Insta-Cure Super Thin Filling CA Glue

    $5.95$20.49
    Insta-Cure cyanoacrylate glue by Bob Smith Industries features a water-thin viscosity that easily seeps deep into joints by capillary action and cures in only a matter of a few seconds. When bonding objects with Bob Smith Industries' Insta-Cure, the surfaces must be tight fitting and should be held together while you apply the cyanoacrylate glue around the edges of the seam. In addition, this glue is also capable of penetrating more than the surface area of the wood creating a stronger bond. Insta-Cure is perfect when gluing balsa wood and ceramics, but also works well for soft woods, fiberglass and hard plastics and is water resistant. When cyanoacrylate glue dries, it dries crystal clear, does not discolor, nor foams making it a great choice for hobby enthusiasts and dental labs. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
  • Bob Smith Insta-Cure Super Thin Pocket CA Super GlueQuick view

    Bob Smith Insta-Cure Super Thin Gap Filling Pocket CA Glue

    $7.99$15.49
    Insta-Cure Pocket CA cyanoacrylate glue by Bob Smith Industries features a water-thin viscosity that easily seeps deep into joints by capillary action and cures in only a matter of a few seconds. When bonding objects with Bob Smith Industries' Insta-Cure, the surfaces must be tight fitting and should be held together while you apply the cyanoacrylate glue around the edges of the seam. In addition, this glue is also capable of penetrating more than the surface area of the wood creating a stronger bond. Insta-Cure is perfect when gluing balsa wood and ceramics, but also works well for soft woods, fiberglass and hard plastics and is water resistant. When cyanoacrylate glue dries, it dries crystal clear, does not discolor, nor foams making it a great choice for hobby enthusiasts and dental labs. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
  • Insta-Cure+ Bob Smith IndustriesQuick view

    Bob Smith Insta-Cure+ Medium Thick CA Super Glue

    $5.95$20.49
    Insta-Cure+ super glue cyanoacrylate features a medium thick viscosity compared to its Insta-Cure CA (thin) and Maxi-Cure (thick) counterparts and is designed for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, Insta-Cure+ should also be used. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
  • Bob Smith Insta-Cure+ Medium Thick Pocket CA Super GlueQuick view

    Bob Smith Insta-Cure+ Medium Thick Pocket CA Super Glue

    $7.99$15.49
    Insta-Cure+ Pocket CA super glue cyanoacrylate features a medium thick viscosity compared to its Insta-Cure CA (thin) and Maxi-Cure (thick) counterparts and is designed for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, Insta-Cure+ should also be used. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
  • Bob Smith Insta-Flex Flexible CA Super GlueQuick view

    Bob Smith Insta-Flex Flexible CA Super Glue

    $9.49
    Bob Smith's Insta-Flex flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, Insta-Flex will not turn brittle and remains clear, even when accelerated with Insta-Set Accelerator. In addition, it has superior shock resistance and although not as thin in consistency as Insta-Cure, Insta-Flex still has good penetrating qualities and its application can be easier to control. For CA hinges, Bob Smith Industries recommends drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when Inta-Flex is applied. Insta-Flex has also proven to be superior when bonding anodized aluminum. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Add to cart
    Compare
  • Bob Smith Insta-Flex+ Flexible CA Super GlueQuick view

    Bob Smith Insta-Flex+ Flexible CA Super Glue

    $9.49
    Bob Smith Industries' Insta-Flex+ clear rubber toughened has similar qualities to its black IC-2000 Tire Glue CA but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000 that gives the CA its black color also contributes to its unsurpassed strength. Since Insta-Fle+ has this carbon removed, its strength is a little less than that of IC-2000, but still superior to standard CA's. When aesthetics are important and a flexible bond is required, Insta-Flex+ is your best choice from Bob Smith Industries. It forms superior bonds to soft urethane and vinyl plastics. Both Insta-Flex and Insta-Flex+ work well when bonding R/C car tires. When a joint has a larger than normal gap, flexible CA's provide superior shock resistant bonds. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Add to cart
    Compare