Description
Sold in packs of 6
Bob Smith CA Extenter Tips #301 (Pack of 6)
$4.49
For use over Bob Smith’s standard #312 top. These be used with all thicknesses of Cyanoacrylate glue from Bob Smith with the except IC-Gel. The flexible tip can be cut to the length and/or inside diameter that is needed for a particular application. Item comes packaged in a pack of 6.
In stock
You may also like…
-
Quick viewBob Smith PTFE Tubing #305 (Pack of 2)
$4.49Two foot length of PTFE tubing which be cut off to any length (usually 2") and used with either Pocket CA caps or the Bob Smith #312 top. This product is designed to be used with thin CA such as a Insta-Cure or Super Gold. By cutting one end cut at a 45° angle, can be inserted 1/8" into Pocket CA top and into #312 top if it is cut down an additional 3/64". For thin CA. This product is commonly used for applying adhesive into hard to reach areas and is commonly used in the dental lab industry. Sold in a pack of 2.Add to cart -
Quick viewBob Smith Extra Fine CA Extender Tips #302 (Pack of 6)
$4.49For use over the standard #312 top from Bob Smith Industries, it allows thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time. Thin CA tends to run everywhere, so these allow precise application.Add to cart -
Quick viewBob Smith CA Extra Long Extender Tips #303 (Pack of 6)
$3.99For use over the standard Bob Smith Industries #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone. Sold in a pack of 6.Add to cart
Related products
-
Quick viewBob Smith Finish-Cure 20 Minute Epoxy
$14.49 – $33.99Bob Smith's Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup. Bob Smith's Finish-Cure 20 Minute Epoxy is has the least discoloration over time. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)Select options -
Quick viewBob Smith Un-Cure CA Debonder
$6.25 – $18.49Bob Smith's UN-CURE debonder will soften cured Cyanoacrylate glue that has been applied fairly recently. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Bob Smith's UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Since cured Cyanoacrylate is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using UN-CURE on plastics. Separating plastics parts with a razor saw is usually the best option. Please Note: The 8 oz. bottles must be shipped ground and therefore can take longer than normal to receive. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest product possible!Select options -
Quick viewBob Smith IC-Gel CA Paste
$7.49Bob Smith Industries IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Bob Smith Industries Maxi-Cure. IC-GEL, although it can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want. It popular with those who either assemble fishing tanks or need to patch a crack in one. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!Add to cart -
Quick viewBob Smith Insta-Flex Flexible CA Super Glue
$9.95Bob Smith's Insta-Flex flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, Insta-Flex will not turn brittle and remains clear, even when accelerated with Insta-Set Accelerator. In addition, it has superior shock resistance and although not as thin in consistency as Insta-Cure, Insta-Flex still has good penetrating qualities and its application can be easier to control. For CA hinges, Bob Smith Industries recommends drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when Inta-Flex is applied. Insta-Flex has also proven to be superior when bonding anodized aluminum. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!Add to cart
Reviews
There are no reviews yet.