Quick viewBob Smith Ultra-Cure Tire Glue CA Super Glue 130
$7.95
Ultra-Cure Tire Glue is a very high performance clear cyanoacrylate that has a medium viscosity (thickness) in-between that of Insta-Cure Super Thin and Insta-Cure+ Gap Filling Medium. It is ideal for the mounting of rubber tires onto remote control R/C car wheels. It is available in our 3/4 oz Pocket CA bottle and comes with one of our new #304 Extender Tip for the Pocket CA pin-in-cap top. ULTRA-CURE can be used in many other applications that require a slightly thicker thin CA and will bond virtually everything.
When using Bob Smith Industries Ultra-Cure Tire Glue, it's important to note that this cyanoacrylate glue gives of a vapor that may irritate the eyes and nose.
Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)
Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
Add to cart
Quick viewBob Smith IC-Gel CA Paste
$7.49
Bob Smith Industries IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Bob Smith Industries Maxi-Cure. IC-GEL, although it can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want. It popular with those who either assemble fishing tanks or need to patch a crack in one.
Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)
Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
Add to cart
Quick viewBob Smith Un-Cure CA Debonder
$6.25 – $18.49
Bob Smith's UN-CURE debonder will soften cured Cyanoacrylate glue that has been applied fairly recently. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Bob Smith's UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Since cured Cyanoacrylate is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using UN-CURE on plastics. Separating plastics parts with a razor saw is usually the best option.
Please Note: The 8 oz. bottles must be shipped ground and therefore can take longer than normal to receive.
Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)
Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest product possible!
Select options
Quick viewBob Smith Finish-Cure 20 Minute Epoxy
$14.49 – $33.99
Bob Smith's Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing.
For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup.
Bob Smith's Finish-Cure 20 Minute Epoxy is has the least discoloration over time.
Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)
Select options
Reviews
There are no reviews yet.