Bob Smith’s Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing.
For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup.
Bob Smith’s Finish-Cure 20 Minute Epoxy is has the least discoloration over time.
Bob Smith's Slow-Cure 30 Minute epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. Slow-Cure can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with Slow-Cure and Finish-Cure to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.
Bob Smith's Slow-Cure 30 Minute Epoxy is the least type of epoxy to discolor over time with the exception of Finish Cure, along with forming bubbles in the resin as it dries.
Bob Smith Industries MID-CURE 15 minute epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUICK-CURE in most applications. MID-CURE is Bob Smith's most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.
Bob Smith's Mid-Cure 5 Minute Epoxy is known to discolor and turn yellow as it ages. Keep this in mind when using it for certain applications.
Bob Smith's Quik-Cure 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. Quick-Cure shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. Quik-Cure is Bob Smith Industries only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with Quik-Cure can be handled after 15 minutes. Full strength is reached in about 1 hour.
Bob Smith's Quik-Cure 5 Minute Epoxy is known to discolor and turn yellow as it ages. Keep this in mind when using it for certain applications.
This product is formerly known as Bob Smith's Quick-Cure 5 Minute Epoxy.
Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle.
Sold in a pack of 5.
Please Note: Caps are not capable of being interchanged with Pocket CA bottles as the diameter of the bottles are different.
Bob Smith's FOAM-CURE is a flexible silicone based adhesive that works very well on EPP and EPO types of foams. It is crystal clear and cures to a more flexible consistency than Cyanoacrylate. It is, however, not instant bonding like Cyanoacrylate and takes roughly 15 to 30 minutes to setup. FOAM-CURE works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE requires exposure to air for drying.
This product is an ORM-D regulated item and must be shipped by ground. This can equate to longer than anticipated delivery times compared to standard Priority & First Class mail packages.
Bob Smith Industries IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as Bob Smith Industries Maxi-Cure. IC-GEL, although it can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want. It popular with those who either assemble fishing tanks or need to patch a crack in one.
Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
For use with Bob Smith Industries Pocket CAs. It slips over the tip of the Pocket CA top to allow for finer application of the CA. With the tip, the CA can be applied to confined areas. Sold in a pack of 6. Bob Smith #314 cap not included.