Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) ">

Cart0

Bob Smith Quick-Cure 5 Minute Epoxy
Bob Smith Quik-Cure 5 Minute Epoxy

Bob Smith Quik-Cure 5 Minute Epoxy

$10.99 – $16.49

Bob Smith’s Quik-Cure 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. Quick-Cure shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. Quik-Cure is Bob Smith Industries only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with Quik-Cure can be handled after 15 minutes. Full strength is reached in about 1 hour.

Bob Smith’s Quik-Cure 5 Minute Epoxy is known to discolor and turn yellow as it ages. Keep this in mind when using it for certain applications.

This product is formerly known as Bob Smith’s Quick-Cure 5 Minute Epoxy.

Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) 

Clear
Add to Wishlist
Compare
SKU: BSI201A Category: Tags: , , , , ,

Description

Bob Smith Industries Quik-Cure 5 Minute Epoxy works best on Hard Woods and Glass and Metal Surfaces, while working great for Balsa Wood, Soft Wood, Fiberglass, Ceramics, Hard Plastics, White Foam and Reinforcing applications.

Refer to the chart below for product uses.

BSI_CHART

Additional information

Size

4.5 oz., 9 oz.
Water Resistant

No
Viscosity

Extra Thick
Brand

Bob Smith Industries

Reviews

There are no reviews yet.

Be the first to review “Bob Smith Quik-Cure 5 Minute Epoxy”

Your email address will not be published. Required fields are marked *

You may also like…

  • Bob Smith Finish Cure 20 Minute EpoxyQuick view

    Bob Smith Finish-Cure 20 Minute Epoxy

    $14.49 – $33.99
    Bob Smith's Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup. Bob Smith's Finish-Cure 20 Minute Epoxy is has the least discoloration over time. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) 
    Select options
    Compare
    Add to Wishlist
  • Bob Smith Mid-Cure 15 Minute EpoxyQuick view

    Bob Smith Mid-Cure 15 Minute Epoxy

    $10.99 – $16.49
    Bob Smith Industries MID-CURE 15 minute epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUICK-CURE in most applications. MID-CURE is Bob Smith's most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength. Bob Smith's Mid-Cure 5 Minute Epoxy is known to discolor and turn yellow as it ages. Keep this in mind when using it for certain applications. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) 
    Select options
    Compare
    Add to Wishlist
  • Slow Cure Bob Smith IndustriesQuick view

    Bob Smith Slow-Cure 30 Minute Epoxy

    $10.99 – $16.49
    Bob Smith's Slow-Cure 30 Minute epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. Slow-Cure can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with Slow-Cure and Finish-Cure to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours. Bob Smith's Slow-Cure 30 Minute Epoxy is the least type of epoxy to discolor over time with the exception of Finish Cure, along with forming bubbles in the resin as it dries. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!) 
    Select options
    Compare
    Add to Wishlist

Related products

  • Bob Smith Foam-Cure Flexible Silicon Foam GlueQuick view

    Bob Smith Foam-Cure Flexible Silicone Foam Glue (Foam Safe)

    $5.99 – $7.99
    Bob Smith's FOAM-CURE is a flexible silicone based adhesive that works very well on EPP and EPO types of foams. It is crystal clear and cures to a more flexible consistency than Cyanoacrylate. It is, however, not instant bonding like Cyanoacrylate and takes roughly 15 to 30 minutes to setup. FOAM-CURE works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE requires exposure to air for drying. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)  This product is an ORM-D regulated item and must be shipped by ground. This can equate to longer than anticipated delivery times compared to standard Priority & First Class mail packages.   
    Select options
    Compare
    Add to Wishlist
  • Bob Smith Super Gold+ Medium Thick Gap Filling Foam Safe CA GlueQuick view

    Bob Smith Super Gold+ Medium Thick Odorless Gap Filling Foam Safe CA Glue

    $8.99 – $23.99
    Bob Smith Industries' Super-Gold+ is an odorless Insta-Cure CAs. It's non-frosting and takes only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes and it's also foam safe on white foam. In addition, Super Gold+ cyanoacrylate will not fog clear plastic and is great for attaching clear plastic canopies. Super-Gold+’s cure to a more flexible consistency for better shock absorption. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, Super-Gold+ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times. If you're looking for a foam safe and odorless CA glue that's a bit thinner, check out Bob Smith's Super Gold CA Glue. It features a thin viscosity and great for filling tight gaps, just like Insta-Cure Super Thin. Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)  Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
    Add to Wishlist
  • Quick view

    Bob Smith Extra CA Tops #312 (Pack of 5)

    $4.49
    Replacement top that is on all of BSI's non-Pocket CAs. Tops can be soaked in acetone overnight to remove any buildup of CA on the inside and outside of the nozzle. Sold in a pack of 5. Please Note: Caps are not capable of being interchanged with Pocket CA bottles as the diameter of the bottles are different.
    Add to cart
    Compare
    Add to Wishlist
  • Bob Smith Un-Cure CA DebonderQuick view

    Bob Smith Un-Cure CA Debonder

    $6.25 – $18.49
    Bob Smith's UN-CURE debonder will soften cured Cyanoacrylate glue that has been applied fairly recently. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Bob Smith's UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Since cured Cyanoacrylate is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using UN-CURE on plastics. Separating plastics parts with a razor saw is usually the best option. Please Note: The 8 oz. bottles must be shipped ground and therefore can take longer than normal to receive.  Free Same Day Shipping* | USPS First Class (2-3 Day Delivery on Average!)  Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest product possible!
    Select options
    Compare
    Add to Wishlist