Bob Smith's Super Gold CA Glue. It features a thin viscosity and great for filling tight gaps, just like Insta-Cure Super Thin. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!">

Cart0

Bob Smith Super Gold+ Medium Thick Gap Filling Foam Safe CA Glue
Bob Smith Super Gold+ Medium Thick Odorless Gap Filling Foam Safe CA Glue

Bob Smith Super Gold+ Medium Thick Odorless Gap Filling Foam Safe CA Glue

$8.99 – $23.99

Bob Smith Industries’ Super-Gold+ is an odorless Insta-Cure CAs. It’s non-frosting and takes only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes and it’s also foam safe on white foam. In addition, Super Gold+ cyanoacrylate will not fog clear plastic and is great for attaching clear plastic canopies.

Super-Gold+’s cure to a more flexible consistency for better shock absorption. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, Super-Gold+ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

If you’re looking for a foam safe and odorless CA glue that’s a bit thinner, check out Bob Smith’s Super Gold CA Glue. It features a thin viscosity and great for filling tight gaps, just like Insta-Cure Super Thin.

Guaranteed Fresh! Our products don’t sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!

Clear
Add to Wishlist
Compare
SKU: BSI126A Category: Tags: , , , , , , , , , , , , ,

Description

Wood can be bonded to white foam with SUPER-GOLD+ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of Insta-Set Accelerator to one piece and apply SUPER-GOLD+ to the other before joining.

Bob Smith's Super Gold+ Super Thin CA Glue comes in four sizes for whatever your project size is (1/2 oz BSI126 / 1 oz BSI127 / 2 oz BSI128)

Refer to the chart below for product uses.

BSI_CHART

Additional information

Viscosity

Medium Thick
Foam Safe

Yes
Size

1 oz., 1/2 oz., 2 oz.
Additional

Water Resistant
Odorless

Yes
Product Type

Cyanoacrylate
Brand

Bob Smith Industries

Reviews

There are no reviews yet.

Be the first to review “Bob Smith Super Gold+ Medium Thick Odorless Gap Filling Foam Safe CA Glue”

Your email address will not be published. Required fields are marked *

Related products

  • Bob Smith Un-Cure CA DebonderQuick view

    Bob Smith Un-Cure CA Debonder

    $6.25 – $18.49
    Bob Smith's UN-CURE debonder will soften cured Cyanoacrylate glue that has been applied fairly recently. If parts are bonded incorrectly or your fingers are stuck together, a few drops of Bob Smith's UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Since cured Cyanoacrylate is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using UN-CURE on plastics. Separating plastics parts with a razor saw is usually the best option. Please Note: The 8 oz. bottles must be shipped ground and therefore can take longer than normal to receive.  Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest product possible!
    Select options
    Compare
    Add to Wishlist
  • Bob Smith Finish Cure 20 Minute EpoxyQuick view

    Bob Smith Finish-Cure 20 Minute Epoxy

    $14.49 – $33.99
    Bob Smith's Finish-Cure 20 minute epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. Finish Cure can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, Finish-Cure should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on Finish-Cure. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. Finish-Cure is best mixed in a disposable cup. Bob Smith's Finish-Cure 20 Minute Epoxy is has the least discoloration over time.
    Select options
    Compare
    Add to Wishlist
  • Bob Smith Insta-Flex Flexible CA Super GlueQuick view

    Bob Smith Insta-Flex Flexible CA Super Glue

    $9.95
    Bob Smith's Insta-Flex flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, Insta-Flex will not turn brittle and remains clear, even when accelerated with Insta-Set Accelerator. In addition, it has superior shock resistance and although not as thin in consistency as Insta-Cure, Insta-Flex still has good penetrating qualities and its application can be easier to control. For CA hinges, Bob Smith Industries recommends drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when Inta-Flex is applied. Insta-Flex has also proven to be superior when bonding anodized aluminum. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Add to cart
    Compare
    Add to Wishlist
  • Bob Smith IC-2000 Rubber Toughened CA Super GlueQuick view

    Bob Smith IC-2000 Tire Glue Rubber Toughened CA Glue

    $8.49 – $10.49
    IC-2000 is a rubber-toughened cyanoacrylate glue that forms superior shock resistant bonds on non-porous surfaces.  The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. IC-2000 is well renowned in the R/C car & truck circuit as being the best adhesive for R/C car tires. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET Accelerator. For model use, IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. When cured, IC-2000 is pliable enough to be carved with a hobby knife. Guaranteed Fresh! Our products don't sit in a warehouse for months, but rather days. We order on a bi-weekly basis from Bob Smith Industries so you are getting some of the freshest cyanoacrylate possible!
    Select options
    Compare
    Add to Wishlist